Description
Brass Brake Blanking Cap M12 x 1mm Female
Solid brass female blanking cap with an M12 x 1mm internal thread and no pipe hole. Screws onto an M12 x 1 male port or hose end to seal it – clutch and brake hoses and lines being stored. Supplied by EMS Spares, Leicester – over 30 years in automotive components.
Specification
| Thread | M12 x 1mm female (1mm pitch) |
|---|---|
| Type | Female blanking cap (solid) |
| Hex / spanner size | N/A |
| Overall length | N/A |
| Material / finish | Solid brass, natural finish – rust resistant, will not seize |
| Interchange reference | HU15AB* |
| EMS part number | EMS-A15AB |
* Reference numbers are for identification and cross-reference only. EMS Spares is an independent UK supplier and has no connection with the owners of these part numbers. All dimensions are approximate.
Buyer’s guide: brake blanking plugs and caps explained
What does a blanking cap do?
A blanking plug or cap seals a brake or clutch port, pipe end or hose that is not in use – for example a spare outlet on a master cylinder or T-piece, a removed pipe while you work, or a system being stored. It seals by seating against the flare seat of the port, in the same way a union clamps a pipe flare, so the thread must match exactly.
Step 1 – identify your thread (the most common mistake)
| Thread | Outside diameter (male part) | Threads | Typically found on |
|---|---|---|---|
| M10 x 1mm | 10mm approx | 1mm pitch (about 25 per inch) | Most European and Japanese cars, many later British cars and kit cars |
| M10 x 1.25mm | 10mm approx | 1.25mm pitch | Some older Italian and French cars (e.g. Fiat, Lancia) |
| 3/8″ x 24 UNF | 9.5mm approx | 24 per inch | Most British classics: MG, Triumph, Mini, Land Rover Series |
| M12 x 1mm (this part) | 12mm approx | 1mm pitch | Larger ports, some master cylinders and 1/4″ pipe |
Tip: M12 x 1 is the larger metric brake thread (12mm across the male thread) – do not confuse it with M12 x 1.25 or 1/2″ x 20 UNF. Check the pitch with a thread gauge.
Step 2 – cap or plug?
- Female blanking cap (this part): screws onto an M12 x 1 male port or hose end.
- Male blanking plug: screws into an M12 x 1 female port – see our EMS-A9B.
How to fit – good practice
- Clean the male port and check the end is free of dirt.
- Start the cap by hand for several turns – it should turn freely.
- Tighten until it seats firmly, holding the hose with a second spanner so it does not twist.
- Check for leaks with the pedal pressed hard.
Safety: brakes are a safety-critical system. If you are not confident, have the work done or checked by a qualified mechanic.
Pack sizes
Available as 2, 3, 4 or 5 caps. Larger packs cost less per piece.
Delivery
Free UK delivery on every order (including Northern Ireland, Highlands & Islands). Same-day dispatch on orders placed before 10am.
Trusted by thousands of buyers on eBay
99.9% positive feedback from over 9,700 ratings, and 5.0 out of 5 for accurate description, postage cost, delivery time and communication (last 12 months). Read our eBay feedback.
FAQ
Is M12 x 1 the same as 1/2″ UNF? No. They look similar but the threads are different and will bind.
Why brass? Brass does not rust or seize, so the blank can be removed again later.
Will it fit a clutch hose end? Yes, where the hose end is an M12 x 1 male thread.
Need help? Message us with your vehicle and the part you are connecting to and we will confirm the right fitting before you order.
Reviews
There are no reviews yet.